Difference between revisions of "MLoader"
From Flowcode Help
Jump to navigationJump to searchLine 21: | Line 21: | ||
==Supported hardware== | ==Supported hardware== | ||
mLoader currently supports the following hardware: | mLoader currently supports the following hardware: | ||
− | *'''EB006''' - E-blocks multiprogrammer supporting 8-bit PIC MCUs: | + | *'''EB006''' - E-blocks multiprogrammer supporting 8-bit PIC MCUs: 12Fxxx, 16Fxxx, 18Fxxxx, 18FxxKxx |
− | + | *'''EB064''' - E-blocks multiprogrammer supporting 16-bit PIC MCUs and dsPIC DSCs: PIC24F, PIC24H, dsPIC30F, dsPIC33F | |
− | + | *'''EB091''' - E-blocks dsPIC33F | |
− | + | *'''EB185''' - E-blocks 32-bit ARM7 programmer | |
− | + | *'''ECIOs''' - Low-cost, single-board computers: 8-bit PIC MCU, 16-bit dsPIC DSC, 32-bit ARM7 | |
− | *EB064 | + | *'''MIAC''' - Rugged PLC-like PIC MCU |
− | + | *'''Formula Flowcode''' - | |
− | + | *'''LKxxxx''' - Locktronics | |
− | + | *'''HP4829''' - Prototype board | |
− | + | *'''HP1110''' - Project board | |
− | |||
− | *EB091 | ||
− | |||
− | *EB185 | ||
− | |||
− | *ECIOs | ||
− | |||
− | |||
− | |||
− | |||
− | *MIAC | ||
− | |||
− | *Formula Flowcode | ||
− | * | ||
− | |||
− | |||
− | *HP4829 Prototype board | ||
− | *HP1110 Project board | ||
==Recent changes== | ==Recent changes== | ||
Recent changes and information on supported chips can be found in the [[mLoader:Recent_Changes]] section of this wiki. | Recent changes and information on supported chips can be found in the [[mLoader:Recent_Changes]] section of this wiki. |
Revision as of 15:09, 22 January 2015
(image here)
Introduction
mLoader is a software application developed by Matrix to reprogram microcontrollers used in a variety of hardware targets.
Modes of operation
There are two basic modes of operation:
- UI mode
- This mode is enabled when mLoader is run as a stand-alone application
- A window is opened (similar to the above image) which allows the user to send and receive programs to the target
- More information can be found here: mLoader:UI_Mode
- non-UI mode
- This mode is typically used when another application (e.g. Flowcode) launches mLoader as part of a build process
- Command line parameters control the operation of mLoader
- No window will usually be opened and use feedback will be provided by the application launching mLoader
- More information can be found here: mLoader:noUI_Mode
Supported hardware
mLoader currently supports the following hardware:
- EB006 - E-blocks multiprogrammer supporting 8-bit PIC MCUs: 12Fxxx, 16Fxxx, 18Fxxxx, 18FxxKxx
- EB064 - E-blocks multiprogrammer supporting 16-bit PIC MCUs and dsPIC DSCs: PIC24F, PIC24H, dsPIC30F, dsPIC33F
- EB091 - E-blocks dsPIC33F
- EB185 - E-blocks 32-bit ARM7 programmer
- ECIOs - Low-cost, single-board computers: 8-bit PIC MCU, 16-bit dsPIC DSC, 32-bit ARM7
- MIAC - Rugged PLC-like PIC MCU
- Formula Flowcode -
- LKxxxx - Locktronics
- HP4829 - Prototype board
- HP1110 - Project board
Recent changes
Recent changes and information on supported chips can be found in the mLoader:Recent_Changes section of this wiki.