Difference between revisions of "Selecting Compiler Options (AVR)"
Line 42: | Line 42: | ||
:C:\Develo~1\Flowcode | :C:\Develo~1\Flowcode | ||
− | + | [[File:Gen_Compiler_Options_Compiler_AVR.png|right|524x400px]] | |
'''%c0''' Configuration byte count | '''%c0''' Configuration byte count | ||
Line 69: | Line 69: | ||
<code>'''$(chip:l) "$(outdir)$(target).elf" "$(outdir)$(target).c" "$(outdir)$(target).lst"'''</code> | <code>'''$(chip:l) "$(outdir)$(target).elf" "$(outdir)$(target).c" "$(outdir)$(target).lst"'''</code> | ||
− | + | [[File:Gen_Compiler_Options_Linker_Assembler_AVR.png|right|524x400px]] | |
− | + | <br /><br /> | |
'''Linker/Assembler location''' | '''Linker/Assembler location''' | ||
Line 89: | Line 89: | ||
There are no default parameters | There are no default parameters | ||
− | + | [[File:Gen_Compiler_Options_Programmer_AVR.png|right|524x400px]] | |
− | + | <br /><br /> | |
'''Programmer location''' | '''Programmer location''' | ||
Line 120: | Line 120: | ||
Note: The above parameters assume you are using the AVRDUDE programming application and AVRISPmkII programmer. If you are using an alternative programming application or programmer you will need to consult the relevant documentation for the required parameters and settings. | Note: The above parameters assume you are using the AVRDUDE programming application and AVRISPmkII programmer. If you are using an alternative programming application or programmer you will need to consult the relevant documentation for the required parameters and settings. | ||
− | + | [[File:Gen_Compiler_Options_File_Viewer_AVR.png|right|524x400px]] | |
− | + | <br /><br /> | |
'''File Viewer location''' | '''File Viewer location''' | ||
Revision as of 14:49, 25 July 2013
<sidebar>Sidebar: Managing Compiler Options</sidebar> Allows users to set the Compiler options.
Options list
See the Managing Compiler Options topic for more information on using this feature.
Substitute variables used by Flowcode
%T Target name as written e.g. atmega32
(generally used by the compiler)
%t Target name forced to lower-case
%p Target name forced to upper-case
%a Alternative target name as written e.g. m32
(generally used by the programmer)
%A Alternative target name forced to upper-case
%f Long file name without extension e.g. C:\Development\Flowcode\TestProgram.fcf becomes:
- TestProgram
%F Short filename without extension e.g. C:\Development\Flowcode\TestProgram.fcf becomes:
- TestPr~1
%d Long file path for the Flowcode file e.g. C:\Development\Flowcode\TestProgram.fcf becomes:
- C:\Development\Flowcode
%D Short file path for the Flowcode file C:\Development\Flowcode\TestProgram.fcf becomes:
- C:\Develo~1\Flowcode
%c0 Configuration byte count
%c1 Configuration byte #1
%c2 Configuration byte #2
%c3 Configuration byte #3
Compiler location
Sets the location of the file controlling compilation
Default:
$(appdir)compilers\avr\batchfiles\avra.bat
Compiler parameters
Adds command line parameters when called from flowcode
Default:
$(chip:l) "$(outdir)$(target).elf" "$(outdir)$(target).c" "$(outdir)$(target).lst"
Linker/Assembler location
Sets the location of the file controlling linking and assembly
Default:
$(appdir)compilers\avr\batchfiles\avrb.bat
Linker/Assembler parameters
Adds command line parameters when called from flowcode
Default:
<empty>
There are no default parameters
Programmer location
Sets the location of the file controlling the programming of the target device
Default:
$(appdir)compilers\avr\batchfiles\avrc.bat
Programmer parameters
Adds command line parameters when called from flowcode
Default:
AVRDUDE $(chipalt) $(chip:l) "$(outdir)$(target).hex" "$(target).hex" 0 $(cfg0) $(cfg1) $(cfg2) $(cfg3)
Use programmer to set configuration options
This box should be left unchecked
Configuration parameters
This box should be left empty. Configuration parameters are set and downloaded from the Build > Configure menu.
Note: The above parameters assume you are using the AVRDUDE programming application and AVRISPmkII programmer. If you are using an alternative programming application or programmer you will need to consult the relevant documentation for the required parameters and settings.
File Viewer location
Sets the File viewer location for viewing C and Assembly files.
Default:
C:\Windows\Notepad.exe
File Viewer parameters
Adds command line parameters for the File viewer program
Default Assembly file viewer:
$(outdir)$(target).lst
Default external program to view source files:
$(outdir)$(target).c