|
|
(3 intermediate revisions by the same user not shown) |
Line 11: |
Line 11: |
| | | |
| __NOTOC__ | | __NOTOC__ |
− | ==BoostC Compiler== | + | |
| + | ==PIC XC8 Compiler== |
| [[File:Gen_Compiler_Options_Compiler_PIC.png|right|524x400px]] | | [[File:Gen_Compiler_Options_Compiler_PIC.png|right|524x400px]] |
| '''Compiler location''' | | '''Compiler location''' |
Line 19: |
Line 20: |
| Default: | | Default: |
| | | |
− | <code>'''$(appdir)compilers\pic\boostc\boostc_$(family:/12F/16F).exe'''</code> | + | <code>'''$(compilerpic)batch\pic_xc8_comp.bat'''</code> |
| | | |
| | | |
Line 28: |
Line 29: |
| Default: | | Default: |
| | | |
− | <code>'''-v -t PIC$(chip:u) "$(target).c"'''</code> | + | <code>'''$(chip) "$(outdir)" "$(target)"'''</code> |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
| | | |
| | | |
− | | + | ==PIC XC8 Linker/Assembler== |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | ==BoostC Linker/Assembler== | |
| [[File:Gen_Compiler_Options_Linker_Assembler_PIC.png|right|524x400px]] | | [[File:Gen_Compiler_Options_Linker_Assembler_PIC.png|right|524x400px]] |
| '''Linker/Assembler location''' | | '''Linker/Assembler location''' |
Line 53: |
Line 40: |
| Default: | | Default: |
| | | |
− | <code>'''$(appdir)compilers\pic\boostc\boostlink_picmicro.exe'''</code> | + | <code>'''$(appdir)tools\DoNothing\DoNothing.exe'''</code> |
− | | |
− | | |
− | '''Linker/Assembler parameters'''
| |
− | | |
− | Adds command line parameters when called from Flowcode
| |
− | | |
− | Default:
| |
− | | |
− | <code>'''-ld "$(appdir)compilers\pic\boostc\lib" libc_$(family:/12F/16F).lib rand_$(family:/12F/16F).lib float_$(family:/12F/16F).lib "$(target).obj" -t PIC$(chip:u) -d "$(outdir:~-1)" -p "$(target)"'''</code>
| |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | ==HI-TECH C Compiler==
| |
− | [[File:Gen_HI-TECH_C_Compiler.png|right|524x400px]]
| |
− | '''Compiler location'''
| |
− | | |
− | Sets the Compiler location.
| |
− | | |
− | Default 10/12/16F:
| |
− | | |
− | <code>'''C:\Program Files (x86)\HI-TECH Software\PICC\PRO\9.83\bin\picc.exe'''</code>
| |
− | | |
− | Default 18F:
| |
− | | |
− | <code>'''C:\Program Files (x86)\HI-TECH Software\PICC-18\PRO\9.80\bin\picc18.exe'''</code>
| |
− | | |
− | | |
− | '''Compiler parameters'''
| |
− | | |
− | Adds command line parameters when called from Flowcode
| |
− | | |
− | Default:
| |
− | | |
− | <code>'''--CHIP=$(chip) -N48 $(target).c'''</code>
| |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | ==HI-TECH C Linker/Assembler==
| |
− | [[File:Gen_HI-TECH_C_Linker_Assembler.png|right|524x400px]]
| |
− | '''Linker/Assembler location'''
| |
− | | |
− | Sets the Assembler program location.
| |
− | | |
− | Default:
| |
− | | |
− | <code>'''$(appdir)\tools\Dummy\DoNothing.exe'''</code>
| |
| | | |
| | | |
Line 124: |
Line 49: |
| Default: | | Default: |
| | | |
− | <code>'''<empty>'''</code> | + | <code>''''''</code> |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
− | | |
| | | |
| | | |
Line 149: |
Line 60: |
| Default: | | Default: |
| | | |
− | <code>'''$(appdir)tools\PPP\PPPv3.exe'''</code> | + | <code>'''$(appdir)tools\mLoader\mLoader.exe'''</code> |
− | | |
− | | |
− | To use the PICkit2 programmer change the location to
| |
− | | |
− | <code>'''$(appdir)tools\PICkit2\pk2cmd.exe'''</code>
| |
− | | |
− | | |
− | To use the PICkit3 programmer change the location to
| |
− | | |
− | <code>'''$(appdir)tools\PICkit3\pk3cmd.exe'''</code>
| |
| | | |
| | | |
Line 168: |
Line 69: |
| Default: | | Default: |
| | | |
− | <code>'''-cs 2 -chip PIC$(chip) -nogui "$(outdir)$(target).hex"'''</code> | + | <code>'''-chip $(chip:u) "$(outdir)$(target).hex"'''</code> |
− | | |
− | | |
− | To use the PICkit2 programmer change the parameters to
| |
− | | |
− | <code>'''-B $(appdir)tools\PICkit2\ -PPIC%p -F$(target).hex -M -A5 -R'''</code>
| |
− | | |
− | | |
− | To use the PICkit3 programmer change the parameters to
| |
− | | |
− | <code>'''-P$(chip) -F$(target).hex -E -M -Y'''</code>
| |
− | | |
− | | |
− | '''Use Programmer to set configuration options'''
| |
− | | |
− | Check box to allow the Programmer application to be used to set up the configuration of the device. This setting needs to be unticked to allow you to use non default programming applications such as the PicKit2.
| |
− | | |
− | | |
− | '''Configuration parameters'''
| |
− | | |
− | Supplies the command line parameters needed for configuration.
| |
− | | |
− | Default:
| |
− | | |
− | <code>'''-cs 2 -chip PIC$(chip) -config'''</code>
| |
− | | |
− | Note: The above Programmer defaults assume that you are using the PPP Programming application from Matrix Multimedia.
| |
− | If you are using an alternative programming application you will need to consult the documentation for that application for the required parameters and settings.
| |
− | | |
− | Additionally configuration words can be embedded into the program using the Supplementary code feature, or C Code icons.
| |
− | | |
− | | |
− | For help using the PicKit2 Programmer with Flowcode, untick the "Use Programmer to set configuration options" button and then click here to view the configuration settings required.
| |
− | | |
− | | |
− | ==File Viewer==
| |
− | [[File:Gen_Compiler_Options_File_Viewer_PIC.png|right|524x400px]]
| |
− | '''File Viewer location'''
| |
− | | |
− | Sets the File viewer location for viewing C and Assembly files.
| |
− | | |
− | Default:
| |
− | | |
− | <code>'''C:\Windows\Notepad.exe'''</code>
| |
− | | |
− | | |
− | '''File Viewer parameters'''
| |
− | | |
− | Adds command line parameters for the File viewer program
| |
− | | |
− | Default Assembly file viewer
| |
− | | |
− | <code>'''$(outdir)$(target).asm'''</code>
| |
| | | |
− | Default external program to view source files
| |
| | | |
− | <code>'''$(outdir)$(target).c'''</code>
| + | [[Supporting_Third_Party_Programming_Tools|Click here for details on using a third party programming e.g. PICkit]] |
<sidebar>Sidebar: Managing Compiler Options</sidebar>
Allows users to set the Compiler options.
Options list
See the Managing Compiler Options topic for more information on using this feature.
Substitute variables used by Flowcode are the same for all platforms.
PIC XC8 Compiler
Compiler location
Sets the Compiler location.
Default:
$(compilerpic)batch\pic_xc8_comp.bat
Compiler parameters
Adds command line parameters when called from Flowcode
Default:
$(chip) "$(outdir)" "$(target)"
PIC XC8 Linker/Assembler
Linker/Assembler location
Sets the Assembler program location.
Default:
$(appdir)tools\DoNothing\DoNothing.exe
Linker/Assembler parameters
Adds command line parameters when called from Flowcode
Default:
'
Programmer
Programmer location
Sets the Programmer application location.
Default:
$(appdir)tools\mLoader\mLoader.exe
Programmer parameters
Adds command line parameters for the Programmer application.
Default:
-chip $(chip:u) "$(outdir)$(target).hex"
Click here for details on using a third party programming e.g. PICkit