Hello Team.
Is there any news regarding the CAN internal module support and USB ,
When should we be expecting support in FC8 or 9
Looking forward to hear some sort of projection, I know we were promised USB support soon just after the initial release of PIC32 support
CAN Support,
Moderator: Benj
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: CAN Support,
Hello Peter,
USB should be in for PIC32 in 7.3.
It's not as neat as the 8-bit and 16-bit devices but it should work if you follow the instructions.
I'll get CAN on the list to investigate for v8.
USB should be in for PIC32 in 7.3.
It's not as neat as the 8-bit and 16-bit devices but it should work if you follow the instructions.
I'll get CAN on the list to investigate for v8.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
- QMESAR
- Valued Contributor
- Posts: 1287
- Joined: Sun Oct 05, 2014 3:20 pm
- Location: Russia
- Has thanked: 384 times
- Been thanked: 614 times
- Contact:
Re: CAN Support,
Hi Ben.
Thank you very much .
I will give it ago .
Much appreciated and this would be great if it would be possible to have CAN in V8
Have good one
Thank you very much .
I will give it ago .
Much appreciated and this would be great if it would be possible to have CAN in V8
Have good one
https://www.flowcodexchange.com/
Regards QMESAR
Regards QMESAR
-
- Posts: 96
- Joined: Fri Jul 15, 2016 10:51 am
- Has thanked: 24 times
- Been thanked: 5 times
- Contact:
Re: CAN Support,
Hi Team, in relation to the question of QMesar about the CAN Controllers for flowcode V8 or V9. There are different CAN controllers on the market that would want to simulate and program using flowcode as described below:
ATA6563
MCP2517FD
ADM3053
STN1110 Multiprotocol OBD
ATA6570
How is this development going and how easy it is to integrate these controllers with in V8, facing this different configurations and setups.
Thank you much
Rod
ATA6563
MCP2517FD
ADM3053
STN1110 Multiprotocol OBD
ATA6570
How is this development going and how easy it is to integrate these controllers with in V8, facing this different configurations and setups.
Thank you much
Rod
-
- Posts: 315
- Joined: Sun Jun 23, 2013 1:29 pm
- Has thanked: 28 times
- Been thanked: 61 times
- Contact:
Re: CAN Support,
Hi
Why doesn't FC just allow us to use the internal CAN interface on a given uC sort out an interrupt for received addresses which have been setup up and have done with it? The actual physical connection can be utilised with interface chips.
Going out and trying to find CAN chips then write specific code for them seems daft.
Why doesn't FC just allow us to use the internal CAN interface on a given uC sort out an interrupt for received addresses which have been setup up and have done with it? The actual physical connection can be utilised with interface chips.
Going out and trying to find CAN chips then write specific code for them seems daft.
-
- Valued Contributor
- Posts: 2045
- Joined: Wed Aug 27, 2008 10:31 pm
- Location: Netherlands
- Has thanked: 553 times
- Been thanked: 1081 times
- Contact:
Re: CAN Support,
It does. For certain uCs. I think there are simply too many different controllers with CAN for Flowcode to support them all.Docara wrote:Why doesn't FC just allow us to use the internal CAN interface on a given uC
“Integrity is doing the right thing, even when no one is watching.”
― C.S. Lewis
― C.S. Lewis
-
- Posts: 315
- Joined: Sun Jun 23, 2013 1:29 pm
- Has thanked: 28 times
- Been thanked: 61 times
- Contact:
Re: CAN Support,
Hi Kersing,
Um are you sure??? I'm looking through my FC7 and I can't see any 'yellow crosses' against any of my CAN components but the only options I can see is for a MCP2515 component which is a SPI to CAN chip.
Or have the last three hairs I have left just turned blonde LOL?
Matt
Um are you sure??? I'm looking through my FC7 and I can't see any 'yellow crosses' against any of my CAN components but the only options I can see is for a MCP2515 component which is a SPI to CAN chip.
Or have the last three hairs I have left just turned blonde LOL?
Matt
-
- Valued Contributor
- Posts: 2045
- Joined: Wed Aug 27, 2008 10:31 pm
- Location: Netherlands
- Has thanked: 553 times
- Been thanked: 1081 times
- Contact:
Re: CAN Support,
Yes, l’m sure. I’ve used the component. I guess you are only looking at 8 bit devices? Some dspic33 devices are supported.
“Integrity is doing the right thing, even when no one is watching.”
― C.S. Lewis
― C.S. Lewis
-
- Posts: 96
- Joined: Fri Jul 15, 2016 10:51 am
- Has thanked: 24 times
- Been thanked: 5 times
- Contact:
Re: CAN Support,
Hi Docara, i wanted to say transceiver, instead of Controller, my mistake. And you re right about the limitation of resources for different mcu while using its internal CAN interface.
Rod
Rod