Microchip Curiosity
- QMESAR
- Valued Contributor
- Posts: 1287
- Joined: Sun Oct 05, 2014 3:20 pm
- Location: Russia
- Has thanked: 384 times
- Been thanked: 614 times
- Contact:
Re: Microchip Curiosity
Hi glennd
There is a Curiosity board supported directly in FC which makes working with it easy and I assume a few people is using it as a development platform.
although there are a few different curiosity boards from Microchip there is one for 8 bit pic one for PIC32 etc I assume the supported board is for 8 bit pic's PIC16 and PIC18 , Is there anything specific about the board you are looking for ?
There is a Curiosity board supported directly in FC which makes working with it easy and I assume a few people is using it as a development platform.
although there are a few different curiosity boards from Microchip there is one for 8 bit pic one for PIC32 etc I assume the supported board is for 8 bit pic's PIC16 and PIC18 , Is there anything specific about the board you are looking for ?
https://www.flowcodexchange.com/
Regards QMESAR
Regards QMESAR
Re: Microchip Curiosity
Hi,
We trying to send a simple programme to the curiosity 8 bit PIC board with the PIC16F18346 chip. Struggling to establish a connection between flowcode and the curiosity board. Is there any setup configurations/drivers/compliers that we may be missing?
Also is it possible to configure a 8 pin chip on the 8 bit curiosity board using flowcode??
Thank you
We trying to send a simple programme to the curiosity 8 bit PIC board with the PIC16F18346 chip. Struggling to establish a connection between flowcode and the curiosity board. Is there any setup configurations/drivers/compliers that we may be missing?
Also is it possible to configure a 8 pin chip on the 8 bit curiosity board using flowcode??
Thank you
- QMESAR
- Valued Contributor
- Posts: 1287
- Joined: Sun Oct 05, 2014 3:20 pm
- Location: Russia
- Has thanked: 384 times
- Been thanked: 614 times
- Contact:
Re: Microchip Curiosity
Hi
In the wiki there is an example how to use the curiosity board in FC however this morning I am not able to download it
may be one of the MATRIX guys can help is with this ,When I try to download the file Flocode tell me to login don't know why
If your board has a Pickit3 on board you can try to set it up in Flowcode to allow programming as shown in this wiki page
https://www.matrixtsl.com/wikiv7/index. ... _.28NEW.29
In the wiki there is an example how to use the curiosity board in FC however this morning I am not able to download it
may be one of the MATRIX guys can help is with this ,When I try to download the file Flocode tell me to login don't know why
If your board has a Pickit3 on board you can try to set it up in Flowcode to allow programming as shown in this wiki page
https://www.matrixtsl.com/wikiv7/index. ... _.28NEW.29
https://www.flowcodexchange.com/
Regards QMESAR
Regards QMESAR
- QMESAR
- Valued Contributor
- Posts: 1287
- Joined: Sun Oct 05, 2014 3:20 pm
- Location: Russia
- Has thanked: 384 times
- Been thanked: 614 times
- Contact:
Re: Microchip Curiosity
Forgot,
I don't think that you can run a 8 pin on the board it is designed for the 28 and 40 pin devices the issue is the 8 pin VDD and VSS pins are not lining up with the board or28/40 pin device VDD and VSS
I don't think that you can run a 8 pin on the board it is designed for the 28 and 40 pin devices the issue is the 8 pin VDD and VSS pins are not lining up with the board or28/40 pin device VDD and VSS
https://www.flowcodexchange.com/
Regards QMESAR
Regards QMESAR