Page 1 of 1
Flowcode v3.2
Posted: Fri May 25, 2007 5:36 pm
by Steve
Sorry folks...
...but v3.2 is not available.
I've been working flat out all week on this and I've got it all sorted except for one thing - the actual installation. I've tried and failed to get this installer working, but I've not been able to successfully.
I am now going on holiday for a week, so nothing will happen for a while.
But I did promise you some updated files, and those wanting to manually update their copy of Flowcode with the appropriate files will need to contact Ben directly (
support@matrixmultimedia.co.uk).
Ben will post here what "patches" will be available on Tuesday.
I strongly recommend that only those users who have an urgent need for an update (e.g. for I2C) actually ask for the patches.
Again, I'm really sorry for not getting this update out on time. I didn't want to release something half-baked, so hopefully I'll get something better to you in a few weeks time.
Posted: Fri May 25, 2007 5:58 pm
by Benj
The patches that will be available from Tuesday 29th May are as follows:
Master I2C Component
Lin Master and Slave Component
PWM Component
Updated LCD Component
Updated Keypad Component
Updated EEPROM Component
Updated Bluetooth Component
Also a variety of bug fixes and run time tweaks
Improved FCD Files.
Added Languages including Romanian and Danish
Let me know by email if you wish to receive the update.
ben@matrixmultimedia.co.uk
or
support@matrixmultimedia.co.uk
flocod 3.2 update
Posted: Tue May 29, 2007 1:51 pm
by saschech@gmx.de
Hallo Ben
Thanks for the files.I have do what the install-doku says.
I cannot find the new symbols in the komponent-bar into flocode.
There is not a information in the "sort component window" for the new
komponents.
The eeprom komponent is updatet (i show 1024 bytes).
The new version i can also show 3.2.0.36
What can i do ?
wolfgang
Posted: Tue May 29, 2007 4:06 pm
by Benj
Hello
Did you follow the readme file when adding the V3.2 files.
You need to run the Install New Components Batch file. This should add the new components to your Flowcode.
i2c update
Posted: Wed May 30, 2007 9:15 am
by saschech@gmx.de
Hello Ben
Correct these I have do. I show the dos-window any new components
regsvr.....ocx ok. anyway i cannot show it in the flocode component bar.
Regards wolfgang
Posted: Wed May 30, 2007 9:41 am
by Benj
Thats strange.
Are you sure that you placed the component files into the correct folder.
Flowcode V3/Components
If you have already done this then maybe try uninstalling and reinstalling from the last full install and then try performing the update again.
I2C available?
Posted: Thu Jun 07, 2007 2:36 am
by MarcB
is the I2C component available?
Where can I download it?
Or can you mail it?
marc@vegasnet.nl
Thanks
Posted: Thu Jun 07, 2007 6:29 pm
by tibor
hello Benj
I have the same problem as sasches.I install your patch by your instruction , but i dinΒ΄t see new macros(PWM,LIN,IIC...),but if I edit
CompCats.reg than I saw this icons but didnΒ΄t work correctly.flow version 3,2... .
best regards
tibor
PWM
Posted: Sat Jun 09, 2007 9:15 am
by tibor
Hello Benj
I have a question for you.I want to use 3 or 6 pwms in flow .it will be program for RGB led ,but I can to use only 2 pwm.I send you one picture
by mail, becouse i donΒ΄t know ,what does it mean this icon with question mark.
thank you Benj
best regards tibor
ps:yours updates are very nice
Posted: Mon Jun 11, 2007 9:27 am
by Benj
Hello Tibor
Currently there are only two PWM outpout options for Flowcode. This should increase in the future but is not likely to be for a little while. For the moment you could always emulate the third PWM by creating a timer interrupt that turns a pin on or off at a specific frequency.