Hallo Benj
By praxis delay 100ms is ca. 1sec.
1sec is ca. 10sec.
C:\Programme\Matrix Multimedia\Flowcode V3\BoostC\boostlink.pic.exe -ld "C:\Programme\Matrix Multimedia\Flowcode V3\BoostC\lib" libc.pic18.lib flowcode.pic18.lib "sapimu_18f8722.obj" -t PIC18F8722 -d "D:\sapimu_18f8722" -p "sapimu_18f8722"
BoostLink Optimizing Linker Version 6.85
http://www.sourceboost.com
Copyright(C) 2004-2008 Pavel Baranov
Copyright(C) 2004-2008 David Hobday
Caution: Delay inaccurrate: 'delay_ms', Delay overhead:0ms, Unit delay:1.00006ms, Delay resolution:1 units
Building CASM file
Memory Usage Report
===================
RAM available:3936 bytes, used:6 bytes (0.2%), free:3930 bytes (99.8%),
Heap size:3930 bytes, Heap max single alloc:127 bytes
ROM available:131072 bytes, used:226 bytes (0.2%), free:130846 bytes (99.8%)
success
Return code = 0
FINISHED
Regards wolfgang
Delay error pic 18f8722
-
- Posts: 714
- Joined: Wed Jan 31, 2007 12:41 pm
- Has thanked: 1 time
- Been thanked: 26 times
- Contact:
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: Delay error pic 18f8722
Hello Wolfgang
Is the clock in Flowcode set correctly. Also are you using the Crystal Oscillator or the RC oscillator.
The speed in Flowcode must match your hardware crystal speed or the RC speed. Flowcode does not control the speed it merely conforms to it.
Is the clock in Flowcode set correctly. Also are you using the Crystal Oscillator or the RC oscillator.
The speed in Flowcode must match your hardware crystal speed or the RC speed. Flowcode does not control the speed it merely conforms to it.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
-
- Posts: 714
- Joined: Wed Jan 31, 2007 12:41 pm
- Has thanked: 1 time
- Been thanked: 26 times
- Contact:
Re: Delay error pic 18f8722
Hallo Benj
The Oscillator config bit was wrong; thankyou.
Question more:
If i build the *.asm in flowcode and program with MPlab icd2, where are the place
to adjust the config bits correct?
Regards wolfgang
The Oscillator config bit was wrong; thankyou.
Question more:
If i build the *.asm in flowcode and program with MPlab icd2, where are the place
to adjust the config bits correct?
Regards wolfgang
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: Delay error pic 18f8722
Hello
Flowcode embedds the config bits into the hex file so if you are sending the hex file via MPLAB then you should be OK. However if you are compiling the Assembler code with MPLAB then you will need to set the config bits in the Configure Menu.
Flowcode embedds the config bits into the hex file so if you are sending the hex file via MPLAB then you should be OK. However if you are compiling the Assembler code with MPLAB then you will need to set the config bits in the Configure Menu.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel