MOD Operation selected after Minut

For MIAC users to discuss projects, applications, and any other issues related to the MIAC unit.

Moderators: Benj, Mods

Monie Jacobsen
Posts: 484
Joined: Mon Jul 30, 2012 3:39 pm
Has thanked: 17 times
Been thanked: 46 times
Contact:

Re: MOD Operation selected after Minut

Post by Monie Jacobsen »

Hi kersing
Rigtigt mange tak.
Never used these terminals before. But is now connected as you refer to;-)
"

Code: Select all

You need to connect to Miac RX and TX, the pins upper right, next to the power connector
"

Here' I do not really know what you mean here!
"And of course set the component to use that serial port"
Is it RX Remap Pin Port E.1. Or what do you mean? Should "Port E.1" be connected to a serial port. Where is this "serial port"?
Serial port.JPG
Serial port.JPG (72.55 KiB) Viewed 9101 times
Best Regard
Monie

kersing
Valued Contributor
Valued Contributor
Posts: 2045
Joined: Wed Aug 27, 2008 10:31 pm
Location: Netherlands
Has thanked: 553 times
Been thanked: 1081 times
Contact:

Re: MOD Operation selected after Minut

Post by kersing »

The serial port settings you show are correct IF the jumper settings in the Miac are correct. Check the data sheet to see the jumper settings (page 11, one of the first three diagrams is OK)

Check the documentation of your GPS module to see if it uses 9600 bps or 38400 bps for the communication speed.
“Integrity is doing the right thing, even when no one is watching.”

― C.S. Lewis

Monie Jacobsen
Posts: 484
Joined: Mon Jul 30, 2012 3:39 pm
Has thanked: 17 times
Been thanked: 46 times
Contact:

Re: MOD Operation selected after Minut

Post by Monie Jacobsen »

Hi kersing
Thank you very much.
Looking at it tomorrow. OK ;-)
Best Regard
Monie

Monie Jacobsen
Posts: 484
Joined: Mon Jul 30, 2012 3:39 pm
Has thanked: 17 times
Been thanked: 46 times
Contact:

Re: MOD Operation selected after Minut

Post by Monie Jacobsen »

Hi kersing
Would like to be careful here not to pills too much in dsPIC Miac!
Can you see which jumper to move And to which??
RS232.JPG
RS232.JPG (171.4 KiB) Viewed 9091 times
Best Regard
Monie

kersing
Valued Contributor
Valued Contributor
Posts: 2045
Joined: Wed Aug 27, 2008 10:31 pm
Location: Netherlands
Has thanked: 553 times
Been thanked: 1081 times
Contact:

Re: MOD Operation selected after Minut

Post by kersing »

Please check the documentation. I mentioned the page and settings in my previous message.
“Integrity is doing the right thing, even when no one is watching.”

― C.S. Lewis

Monie Jacobsen
Posts: 484
Joined: Mon Jul 30, 2012 3:39 pm
Has thanked: 17 times
Been thanked: 46 times
Contact:

Re: MOD Operation selected after Minut

Post by Monie Jacobsen »

Hi kersing
Which jumper settings in the Miac are correct????
Is this this jump settinge to be used below?
RS232_use.JPG
RS232_use.JPG (11 KiB) Viewed 9084 times
Best Regard
Monie

kersing
Valued Contributor
Valued Contributor
Posts: 2045
Joined: Wed Aug 27, 2008 10:31 pm
Location: Netherlands
Has thanked: 553 times
Been thanked: 1081 times
Contact:

Re: MOD Operation selected after Minut

Post by kersing »

one of the first three diagrams is OK
So that one is correct, but the settings in your picture are correct as well.
“Integrity is doing the right thing, even when no one is watching.”

― C.S. Lewis

Monie Jacobsen
Posts: 484
Joined: Mon Jul 30, 2012 3:39 pm
Has thanked: 17 times
Been thanked: 46 times
Contact:

Re: MOD Operation selected after Minut

Post by Monie Jacobsen »

Hi kersing
So burned off GPS :(
Best Regard
Monie

kersing
Valued Contributor
Valued Contributor
Posts: 2045
Joined: Wed Aug 27, 2008 10:31 pm
Location: Netherlands
Has thanked: 553 times
Been thanked: 1081 times
Contact:

Re: MOD Operation selected after Minut

Post by kersing »

Have you checked the gps documentation for the default communication settings?

If you happen to have a serial to usb converter you can connect the gps to it to check it is working as expected.
“Integrity is doing the right thing, even when no one is watching.”

― C.S. Lewis

Monie Jacobsen
Posts: 484
Joined: Mon Jul 30, 2012 3:39 pm
Has thanked: 17 times
Been thanked: 46 times
Contact:

Re: MOD Operation selected after Minut

Post by Monie Jacobsen »

Hi kersing

Have both before and now where GPS does not work anymore.
And test the GPS device on ardunie uno.
So GPS is OFF ;-)
Best Regard
Monie

Post Reply