EB185 Will Not enter programming mode.
EB185 Will Not enter programming mode.
With EX 1 loaded, the build process works fine, it compiles with no errors and ends the process with Exit Code: 0. As soon the Program Device is started I get the instruction to Connect the device to USB Port & enter programming mode by holding ‘Prog’ button & tapping the ‘Reset” button. Before I can read it, the message is removed I get the message: “Bad response received.” Does anyone have any idea what is going on?
- DavidA
- Matrix Staff
- Posts: 1076
- Joined: Fri Apr 23, 2010 2:18 pm
- Location: Matrix Multimedia Ltd
- Has thanked: 58 times
- Been thanked: 258 times
- Contact:
Re: EB185 Will Not enter programming mode.
Hello Jim,
Are you using Flowcode for ARM or the C4ARM coursE?
Are you using Flowcode for ARM or the C4ARM coursE?
- DavidA
- Matrix Staff
- Posts: 1076
- Joined: Fri Apr 23, 2010 2:18 pm
- Location: Matrix Multimedia Ltd
- Has thanked: 58 times
- Been thanked: 258 times
- Contact:
Re: EB185 Will Not enter programming mode.
Hello Jim,
Have you installed the drivers for the Eb185 from our website? http://www.matrixmultimedia.com/lc_index.php?p=17
Also what operating system are you using to run the course? Is it 32 or 64bit?
Have you installed the drivers for the Eb185 from our website? http://www.matrixmultimedia.com/lc_index.php?p=17
Also what operating system are you using to run the course? Is it 32 or 64bit?
Re: EB185 Will Not enter programming mode.
Hi! David,
I'm trying to get the EB185 run on Windows 7 ( 32 bit ) but have had no success. I was told I needed SAM-BA v2.8 but I have been unable to locate a copy. Most of my confusion arises out of old imformation, and old drivers. I could really use the latest copy of insturctions on how to re-flash the ARM Board and how to Install the USB Bootloader; also when to do either or both. I'll investigate the link you recomended.
Thanks,
Jim
I'm trying to get the EB185 run on Windows 7 ( 32 bit ) but have had no success. I was told I needed SAM-BA v2.8 but I have been unable to locate a copy. Most of my confusion arises out of old imformation, and old drivers. I could really use the latest copy of insturctions on how to re-flash the ARM Board and how to Install the USB Bootloader; also when to do either or both. I'll investigate the link you recomended.
Thanks,
Jim
Re: EB185 Will Not enter programming mode.
Hello Again Dave,
No luck with the website. I couldn’t identify anything I could recognize. I did down load the Technical Datasheet for the ARM Programmer & Daughter Board; But understand some instructions need to be updated for the EB185 to operate correctly with Windows 7.
No luck with the website. I couldn’t identify anything I could recognize. I did down load the Technical Datasheet for the ARM Programmer & Daughter Board; But understand some instructions need to be updated for the EB185 to operate correctly with Windows 7.
- Benj
- Matrix Staff
- Posts: 15312
- Joined: Mon Oct 16, 2006 10:48 am
- Location: Matrix TS Ltd
- Has thanked: 4803 times
- Been thanked: 4314 times
- Contact:
Re: EB185 Will Not enter programming mode.
Hello,
The SAM-BA 2.8 software can be downloaded from here.
http://www.matrixmultimedia.com/softwar ... _Setup.exe
We are currently looking into the 2.11 version of SAM-BA to see if it really is compatible with the chips. Other versions released after 2.8 listed compatibility but did not seem to actually work correctly with the ARMSAM7S devices.
Also please check that the I/O and USB jumper is in the USB position and that it is making horizontal connections as shown on the picture on the datasheet.
http://www.matrixmultimedia.com/resourc ... 5-30-1.pdf
Let us know how you get on.
The SAM-BA 2.8 software can be downloaded from here.
http://www.matrixmultimedia.com/softwar ... _Setup.exe
We are currently looking into the 2.11 version of SAM-BA to see if it really is compatible with the chips. Other versions released after 2.8 listed compatibility but did not seem to actually work correctly with the ARMSAM7S devices.
Also please check that the I/O and USB jumper is in the USB position and that it is making horizontal connections as shown on the picture on the datasheet.
http://www.matrixmultimedia.com/resourc ... 5-30-1.pdf
Let us know how you get on.
Regards Ben Rowland - MatrixTSL
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Flowcode Product Page - Flowcode Help Wiki - Flowcode Examples - Flowcode Blog - Flowcode Course - My YouTube Channel
Re: EB185 Will Not enter programming mode.
Hello Benji,
Thanks for the link. Although the message claimed this was SAM-BA 2.83, the screen presentation was marked SAM-BA 2.7.
That said, I went on to remove driver listed in the USB section of the Device Manager.
Once the USB driver was removed I went on to install the new driver, that ID’d itself as: AT91 USB to Serial Converter (COM11).
I started SAM-BA 2.7; Entered ‘ COM11’ to select the connection. And, typed in the board type: AT91SAM7S128-EK. Selecting the ‘Connect’ button I got the following Message: “Failed to open connection”, and the board type kept reverting back to: ‘AT91CAP9-DK-MB’
I could really use some help with this thing. You got any ideas?
Jim
Thanks for the link. Although the message claimed this was SAM-BA 2.83, the screen presentation was marked SAM-BA 2.7.
That said, I went on to remove driver listed in the USB section of the Device Manager.
Once the USB driver was removed I went on to install the new driver, that ID’d itself as: AT91 USB to Serial Converter (COM11).
I started SAM-BA 2.7; Entered ‘ COM11’ to select the connection. And, typed in the board type: AT91SAM7S128-EK. Selecting the ‘Connect’ button I got the following Message: “Failed to open connection”, and the board type kept reverting back to: ‘AT91CAP9-DK-MB’
I could really use some help with this thing. You got any ideas?
Jim
Re: EB185 Will Not enter programming mode.
Hello
I am having the same problem. I have WIndows 7 32 bit running in a VM under vmware fusion.
I have installed the c for ARM courseware and can sucessfully compile.
I have installed Samba 2.7 and it appears that I can re-flash the e-blocks 185 board. I followed the above procedures according to the 185 .pdf file.
I selected the USB/ARM port and was able to send the bin file to the board without errors.
But I still get the "Bad response received" error message after I press the program and hit reset and wait awhile, (When I try to run the ARM Test Program)
I have looked on the driver section, but I cannot find the eb185 drivers. when I search for eb185 I just see the .pdf file.
When I look in the device manager I do not see any device for the matrix board.
But I do sometimes hear the windows usb tones when I hit the Program and reset buttons.
Any help would be greatly appricated.
Thanks
Joe
I am having the same problem. I have WIndows 7 32 bit running in a VM under vmware fusion.
I have installed the c for ARM courseware and can sucessfully compile.
I have installed Samba 2.7 and it appears that I can re-flash the e-blocks 185 board. I followed the above procedures according to the 185 .pdf file.
I selected the USB/ARM port and was able to send the bin file to the board without errors.
But I still get the "Bad response received" error message after I press the program and hit reset and wait awhile, (When I try to run the ARM Test Program)
I have looked on the driver section, but I cannot find the eb185 drivers. when I search for eb185 I just see the .pdf file.
When I look in the device manager I do not see any device for the matrix board.
But I do sometimes hear the windows usb tones when I hit the Program and reset buttons.
Any help would be greatly appricated.
Thanks
Joe
- DavidA
- Matrix Staff
- Posts: 1076
- Joined: Fri Apr 23, 2010 2:18 pm
- Location: Matrix Multimedia Ltd
- Has thanked: 58 times
- Been thanked: 258 times
- Contact:
Re: EB185 Will Not enter programming mode.
Hi Joe,
This was an oversight and i have added the drivers for the ARM device onto the Learning Centre.
http://www.matrixmultimedia.com/lc_index.php?p=17
please try this and let me know if it helps
This was an oversight and i have added the drivers for the ARM device onto the Learning Centre.
http://www.matrixmultimedia.com/lc_index.php?p=17
please try this and let me know if it helps
Re: EB185 Will Not enter programming mode.
Hi David,
Thanks for the link on the drivers. I will try them out when I get home tonight.
Joe
Thanks for the link on the drivers. I will try them out when I get home tonight.
Joe
Re: EB185 Will Not enter programming mode.
Hi David,
I went back and re-flashed again. This time everything works just fine. I am now able to run the test program. I can use SAM-BA to load .bin files and I can load .bin files from Programmers NotePad
I am off and running.
Thanks for the assistance
Joe
I went back and re-flashed again. This time everything works just fine. I am now able to run the test program. I can use SAM-BA to load .bin files and I can load .bin files from Programmers NotePad
I am off and running.
Thanks for the assistance
Joe