Matrix user forums

hey Benj
yes I thing it is that .
I downloaded now I will see the result Later to day or tomorrow
sorry Fridays are my small out side woirk.
with regards
Nasim

hey Ben J
now all connection are ok as lots of USB arrived today .
but for transferring data to the chip I need to have Version 3.9 1226 to get the work done
looking forward hearing from you
wr
Nasim

Dear adviser Can you kindly send me the software of EB-006-00-7 Programmer now I have been using Dataman programmer evry thing shows ok but I am not receiving data out puts . it must be a mistake on setting of some function . when I bought EB-00-600-7 i have not received the small compact disk with...

thanks BenJ I have only one DC out put of 18 volt ,1A. it has been divided for what was needed sorry that I only sent you one part of the processors circuit diagram the 5v1 is an output from stablizer L7805cv = 5v1 ,500mA 3v3 to 5 is the out put is from : L7805cv+10ohm R+ 3v3 Zenor diode out put is=...

Hey BenJ the connections of the attached diagram shows the pin (1) of the IC is connected to 5v1 through a 10K Resistor & a switch to GND I have also set a text "Good luck" it shows after every sec I hope I will be able to make this work I have been using allots your time & mine with regards Nasim

[quote="Nasim Khaliqhey"]hey dear Ben j to day I received the 16MHZ Crystal & 22pf capacitors and for security of runing the program I made the delay 1 sec the result is the same No display please have a look at attached copies there must be some thing that I don´t know in configurations to be corre...

Hey dear Adviser I am using 2 Scope with 3 Channels I see good square pulses in average of 3.5 v by using NAND gate IC CD 4011B I have ordered Volt Amplifier ICs it will take time to receive them lets this case sleep for a two or three weeks then I will come back to you if I need your help so far so...

hey dear adviser I don´t know what is wrong I made the modification as you can see in the attached snapshot the result is the same. can I can come to you to find this problem or please think about it if the change of Chip would make a deference I have to find a solution for this even if I have take ...

Nasim[/quote]dear adviser thanks for your useful information
Do you mean LVP should be disable or to disable the interrupt ?
sorry about that I can not find IOC in my Programmers software
sorry for being for taken your time
it my first project in programming PICs.
wr
Nasim

dear adviser thanks for your useful information
Do you mean LVP should be disable ?
sorry about that I can not find IOC in my Programmers software
sorry for being for taken your time
it my first project in programming PICs.
wr
Nasim

hey dear adviser
here I send you the drawing of the switching transistor circuit as I have mentioned in my last post
wr
nasim

Note: the last two Transistors in second drawing are NPN.

dear adviser here attached the icons setting diagram done by me
answer to question of prop GRD connection I am 100% shore about that other ways I will not be reading any thing
I will be soon send you the diagram of switching transistors hope you find the mistakes .
with regards
Nasim

hey dear Ben J I made the designed software transaction to PIC16F877A by your advice of making the delet timing to 0.1sec=1ml sec . To amplify the voltage for driving an LED I used a NPN transistor with low currant base drive I tested even tech it by finger the LED turns ON . then I tried with PNP t...

Hey dear Benj I hope I am not using your other working time, this project has also taken allots of my workshop working hours + my evenings away from my family never mind now my EB00-6 00-7 is working and I programmed an other PIC16F877A for reading a constant I tried by adding a diode 1 PNP & 1 NPN ...

hey Ben J thanks for your use full calculation info it has been successfully used now for timing of gates operations. I set 8 MHz crystal & reset the delet time to 68s But as I see I have to set the LEDs Anodes to gates by using NPN transistors please have a look at the Attached snapshots kindly tel...

Thanks for showing me how to calculate the delay timing all your advice are grate . now I can read some thing like 0,123 volt for a few second 00.00 volt for a few seconds . with my multi meter that is giving the unwanted blinks to LED s I am going to add 200Kohm resistor between B0.......7 &VDD I w...

Dear adviser Can you kindly send me the software of EB-006-00-7 Programmer now I have been using Daman programmer evry thing shows ok but I am not receiving data out puts . it must be a mistake on setting of some function . when I bought EB-00-600-7 i have not received the small compact disk with I ...

dear adviser
yes always two 0.1nf dc blacker been set between the two pins of crystal & Grd (-)

2016-12-07 (2).png hey Ben J can you please have a look at my work notes to find my mistakes ? Connection notes: 1-MLCR connected to 4v9 via 10 k resistor & a switch for reset 2-A0 has been tried by inserting 3v3 or 4v9 3-A4 is connected to Clock pin 13 4-I used a Zenor Diode of 5v1 with 10R resist...

thanks
I will take a small photos of my drawings and send to you .
as we all know it is Christmas month we are all busy
but I hope to get some where to success this project.
thanks again
wr
Nasim

Dear Benj thanks for your last information of placing the initalising gLCD be for the Loop that is making the action of display faster in my laptop but still I could n`t get the data display in my EBM001 here I attach some of my work the Bread board I made are supplying the right voltages & current ...

Dear adviser
thanks for you information sorry I am late but I am sending you a copy of my software work
see if you can find a way to make it work with the mentioned display

with regards
Nasim

dear Leigh M
Thanks allot for you use full advice
but it is the same can you kindly look at the attached configurations there must be some mistakes here I can not send the all document snap shots more then 3 please advice me which ones to choose
with regards
Nasim

hey dear Ben j
I don´t know why my post has not reached you may be it is my Rooter is not able to do that .
here I send you a copy of my last project hope that I can get the advice to make it work.
Wr
Nasim

Dear Benj T o day I received 2 of gLCD EBM001 but they don´t have any IC at the back side of gLCD´s PCB but there are 8 transistors and some other smd components I spend a few hours to get it work but the problem is the same only back light is working no data appears please see what can be done to m...