Matrix user forums

Hi Benj,
finally it works.The only problem I have is that if I enable both A6 & A7 as I/O the prossesor stuck after 1 sec. If the A6 is configured as a Clockout port the PIC is fine...One I/O less!
Thank you for your help!

Hi Benj, still refuse to work...any other idea or I will use a crystal?
Regards

Hi benj,
doing the config below, I have 4 sec pulce but changing the osccon to 70 it stucks. I need 4 times faster pulses. Maybe the PLL is not enabled...
Regards
Sakis

Thank you for your reply Benj but it doesn't work. First didn't complete the compilation because the osccon was in capital letters(!). After that just bring the first word 0x55 and stop there. I tried to change some parameters from the config but no success...
Sakis

Hello Matrix and forum people!
Help me with config file for the pic 18f25k22. I want the internal oscillator 4x PLL and 16 MHz osc. So far I couldn't manage to do that... Give me a solution please!!!
Thank you!
Sakis

Thank you very much all of you for your reply...unfortunatelly I used the smd version and I made a pcb for that. Bad luck!
Thanks again!
Sakis

Good morning Flowcode people, trying to compile I have the error below... Is there any idea about the problem? Thank you Sakis Target folder: Z:\FlowCode\F9XVES~H Source name: Z:\FlowCode\FlowCode_6\220_tst.fcfx Title: Description: Device: PIC.10F.10F220 Generated by: Flowcode v6.0.10.0 Date: Monday...

It works! I feel stupid...
Thank you Jac!!!

Hi Jac!
I tryied but I don't have the activation passwords only the purschacing password and when I try to create a new one it says that this pwd has consumed.
Sakis

Good morning Matrix people! Doing update to version 9 and 10 last night, I lost my lisences and from prof use I now have home edition. Finally it was downgrade... Is there any soloution to that?
Sakis

Hi everybody,
running the servo example 1, in the component example page, is ok but trying to compile it I have error issues. The second example with the two servos is fine. What is going wrong?
Sakis

Hi Martin again, two of the three pieses I told you I did it in the past and worked fine. I did the single pulse timer and was very accurate according to my oscilloscope. My problem is some problems using the v6 programm... For instance now I can't find how to see the values of the variables. In v5 ...

Hi Martin,
the singe pulse from 10 uS to 1 sec, the square wave from 100 kHz to 1 Hz and the string from 2 to 1000 pulses and 10 uS to 0.5 sec period. These are not absolute but somwhere there would be good.
Sakis

Thank you Martin for your advice! I will do that.
Sakis

Thanks again Martin. So it was bad luck by giving the name string to my makro...Where is this keywords written at? Because in the help file wasn't.Better help files and videos will be wellcome. I want to do a pulse genarator with three modes. One to be as a normal gen, the second as a single pulse g...

Thank you very much Martin, now it works! I dont' understand why I had to do it, but it works... I dont' understant also why must spoil somthing it works fine. Could you also answer to me please if from an interrupt can go in a specific point in the main program, because I tried with a connection po...

Hi Matrix people! I feel a bit frustated trying to make a makro in a v6 program but I can't manage to do that so far. What am I doing wrong? I was a happy v4 and v5 user and so I bought the newer version hopping that some issues I had sould be solved. So far I have a lot of problems not doing the qu...

It's fine for me!
Thank you Benj!
Sakis

Hi Flowcode people,
I have a secont PC close to my hardware bench and its very helpfull to me to apply and check directly the software. Do i need a secont licence for that or I can use the exist? My licence is a professional version.
What can I do?
Thank you
Sakis

SCAN_20130104_012553808_small.gif Hi, another solution is to use a secont relay 220vac instead of the push button. The relay will have two contacts(very easy). I send you a patern also with both circuits. The patern with diodes can used also for zero crossing detection in case you want to handle ac...

Hi, Try to connect in series 4-5 1N4001 diodes in series and the same 4-5 in antiparallel. Tie an optocoupler(the led) whith a resistor in series parallel to this diodes so a voltage drop of 2,5-3V being capable to turn on the LED in optocoupler(you have to give some try on that, it depens on the op...

I tried all possible combinations. I also replace the power supply increase it to 14.5 V. Nothing. I don't understand why with 18f4450 is fine, what is the difference between them. I'm almost desperate , I'm thinking to by a programmer...
Sakis

Hello again! I programmed the same board, I could't do with the HP 488 and PPP, with a friend programmer using the Microchip software. The erase and download worked perfect and we did it in two different boards I made. Now I try to reload the hex with HP 488 again and it is not possible. What is goi...

Hello David, yes indeed there is the v3.13 in the tools of v5 but is only executable and I can't install it. Any way when I try to run it I have the message " Registry error:Failed to get data for 'CONFIG 8L' "and when I press OK and run the program PPP I got the same situation as I mention, Scheme ...

Hello,
It is version 3.11.15.30.